Recently, the Australian/New Zealand Bureau of Standards issued AS/NZS 4417.2:2012 Amendment Standard for Electrical and Electronic Products Compliance Marks Fourth Revision A4:2017. The revision expands the list of controlled products, reclassifies the security level of some products, and updates the definition of some products. Six types of products, such as LED bulbs and nightlights, have been added to the scope of compulsory certification products. The standard stipulates that from June 1st, 2018, LED bulbs and nightlights entering the Australian market must first apply for a mandatory safety certificate (commonly known as SAA). details as follows: New Australian Level 3 mandatory control products: In addition to LED bulbs and nightlights, electric heating water bags, DC isolators, glue guns and flexible electric blankets will be enforced on June 1, 2018; New Zealand Level 2 products: Balanced vehicles, DC/AC electric vehicle (EV) charging piles, cable assemblies, line control and protection devices. These products will be sold to New Zealand from June 30, 2017. Relevant test reports that meet the standards are required (you can also apply for a safety certificate); Classification of safety levels: Since June 1, 2018, the three types of flexible heating pads, floor polishers/scrubbers, and TV receivers have been reduced from Level 3 products in Australia to Level 2 products, and deleted from the New Zealand Level 2 list. go with; Product definition updates: Product descriptions such as flexible heating pads, therapy lights, and wall switches have also been updated in this revision. The inspection and quarantine department hereby reminds the export enterprises in the jurisdiction that the LED products are safe voltage products, and the domestic certification system has not been required. Most of the products lack the previous certification work. Therefore, we pay attention to and pay attention to the regulatory access and effective time of each country and the time of entry into force, and make sure that the products meet the latest regulatory requirements of the importing country or region. Waterproof Vertical Mount D-Sub Connectors
waterproof D-sub system is IP67 rated. These panel-mount connectors are available in solder cup as well as right angle and vertical PCB mount types. The cable-mount connector kit includes the connector, which has solder cup contacts. These connectors are available in 9-, 15-, and 25-positions in standard density and 15-, 26-, and 44-positions in high density. The recommended wire gauge for the solder cup connector is 22 AWG to 26 AWG.
These panel-mount waterproof D-subs are designed for rear-mount applications in panels that are up to 2.0 mm thick. They come with two sets of jackscrews. One jackscrew set is 5 mm long for panel thickness up to 1.2 mm, and the other is 6 mm long for panel thicknesses from 1.2 mm to 2.0 mm.
Cable mount D-sub connector kits come with the backshell, seal, thumbscrews, and solder cup connector. They are also easy to install. Simply fit the cable through the backshell, terminate the wire to the solder cup contacts, and hand tighten the cable nut on the rear of the backshell. The backshell will seal a particular range of cable diameters depending on the position count of the connector. Consult the datasheet for specific cable diameter ranges.
Specifications
Current rating
Standard D-sub: 5 A
Hi-density D-sub: 2 A
Breakdown voltage: ≥ AC 500 V/1 minute
Insulation resistance: ≥ 500 MΩ @ DC 500 V
Contact resistance: ≤ 20 mΩ
Material
Contacts: copper alloy, gold-plated
Connector body: nylon 9T or PBT, UL Recognized
Shell: steel, nickel-plated
Applications
DV camcorder
DV VTR
Non-linear editing system
Broadcast monitor
Betacam deck
Panel Mount Waterproof D-Sub Connectors:
Vertical Mount Waterproof D-Sub Connectors:
right angle D-sub waterproof Standard Density, Waterproof Vertical Mount D-Sub Connectors, High Density Waterproof Vertical Mount D-Sub Connectors,IP67 D-Sub Connectors Vertical Mount,Board Mount Waterproof Vertical Mount D-Sub Connectors ShenZhen Antenk Electronics Co,Ltd , https://www.antenkwire.com
Water Proof D-Sub, Standard Density, Male, Panel Mount
Water Proof D-Sub, Standard Density, Female, Panel Mount
Water Proof D-Sub, Standard Density, Female, PCB Mount
Waterproof solder cup, stamped & formed contact D-sub waterproof
solder cup,machined contacts D-sub waterproof
Combo Power + Signal D-Sub Connector, Vertical Mount, Pluge Type,
IP67 rated Combo power D-sub waterproof